Passes & Canyons Blog

The weather on Tuesday was fabulous and I would have ridden but Roy called to say there would be an RMMRC ride out to Kiowa, to Patty Ann’s, on Wednesday, so I changed my plans.

On Wednesday, along with three other guys from the RMMRC, we met up at Performance Cycle and headed south. Dave was leading and he took a common route, heading south on Clinton, then Inverness Drive West, to where we got on Liberty Boulevard, which loops around the south end of Centennial Airport. Then south on Peoria to Ridgegate Parkway where we headed east to Chambers, and then south.

It was then that the surprise came. We came up to Hess Road and the extension past Hess, which they had been working on for some time, was now open and we went straight. I had assumed this was going to be just an entrance into the new housing development that was going up there but boy was I wrong!

A full-blown four-lane semi-expressway now continues south from Hess, and then Chambers bends around to the southeast, crosses Crowfoot Valley Road (which runs diagonally between Parker and Castle Rock), and becomes Bayou Gulch Road, which I knew connected with Parker Road (CO 83) south of the Pinery.

Holy smokes! This newly opened stretch is in fact kind of a beltway through the southeastern part of the metro area that now allows you to get out town without going anywhere near Parker Road except where you cross it on Bayou Gulch Road. This is fabulous!

As I said, Dave was leading and he lives out there just off of Bayou Gulch Road on the east side of Parker Road, and he knew all about this for some time, I guess. He said they had been eagerly awaiting its opening and they are so glad it finally is. Wow, so am I.

So the rest of the ride was good. As we often do, we took Bayou Gulch on to where it hits Flintwood Road and then took that south to CO 86, then east to Kiowa. Had a good breakfast at Patty Ann’s–as always–and then headed back via the same route so I got to see it again and get a better idea of this new road.

I like this. I can tell I’m going to be riding this road a lot in the future.

Biker Quote for Today

Riding a motorcycle is like living life in high definition.

As I had pretty much expected it would, my old 1980 Honda CB750 Custom has made it to Steele’s Cycle.

I was at Steele’s awhile ago following Tyler as he broke a Ninja down into parts and we were out in the yard at one point. Walking along a row of bikes I saw a bit of blue, a shade of blue that I’m extremely familiar with, and I looked closer. It was my Honda.

The funny thing was that I did not immediately recognize it as being my bike; I only thought it was another bike of the same vintage. I pointed it out to Tyler and he asked if this was in fact my bike and I told him no, it was just another like the one I had.

It wasn’t until that evening over dinner when I was telling Judy about it that it dawned on me that no, of course it was my bike. I had noticed that, hmmm, this CB750 has the same kind of sissybar my bike had. But somehow that had not jarred me awareness. But telling her I realized it was my bike. And I went back to look at it the next time I was at Steele’s and it was so obvious I can hardly believe I didn’t realize that the first time.

There was the same case guard, the same highway pegs, the same side panel on one side from a different year’s model. Of course this was my bike. But when I first saw it it did not have so much that I had come to associate with the bike, stuff I had stripped off the bike at the tow yard when I went to look at it after the crash. Without all that stuff it just didn’t seem like mine.

I pointed it out to Rick Steele and he said that considering I got hit head-on the bike didn’t suffer as much damage as it might have. But when I mentioned the cost of bailing it out of the tow lot he got it instantly–way more to bail it out than it would be worth. He said he gets a lot of bikes from that particular tow lot.

As I said, I was not at all surprised. I expected it would end up there and in fact it has probably been sitting there ever since last summer. Now two of my old bikes are at Steele’s. They’ve had my old Concours for a couple years now and at least it’s sitting inside and may eventually be fixed up and sold. It looks like the Honda is just destined for parts.

If anybody needs some parts for a 1980 Honda CB750 Custom I know where you can find them.

Biker Quote for Today

New Year, New Dreams, New Roads

My previous Shoei helmet gave its life for mine back on June 29 of last year and finally, today, February 17, I got a new one. Or more correctly, Judy did, a Christmas present, to replace the old one which she gave me as a birthday present some years ago. Thank you Judy.

Just a note: it’s not like I’ve been riding without a helmet ever since; like most motorcyclists I have several, but the Shoei was the best of the bunch.

I had looked at various helmets awhile ago and had considered different models and manufacturers but ultimately decided to just go with another Shoei RF-SR.

Judy went with me to Performance Cycle and the sales guy suggested the RF-1400 as an alternative. It cost about $150 more but he said it is quieter and a bit lighter, with the same level of protection.

I may have had some interest in that one considering that he said it comes in a yellow. The RF-SR does not. I could be interested in yellow as being more conspicuous, more visible, but they did not have any in stock. Why? He said very few people actually want a yellow helmet, but he could order it and it would be here in a week.

Judy was pushing me to go for it but quieter and a bit lighter don’t matter that much to me and I was already figuring on getting the RF-SR in white, which should be a lot more visible than my old black one. As long as the protective qualities are equal I just didn’t feel like doing the hassle of coming back when I could walk out today ready to go. Plus, I tried both of them on and the RF-SR felt more comfortable than the RF-1400.

So I went with the RF-SR in white. Then I asked them to transfer my communicator (speakers and wiring) from the old helmet to the new, which I had been told they are happy to do at no charge if you are buying either the helmet or the communicator from them. I’ve been carrying that communicator around in my jacket pocket ever since that crash. I guess I better get it out and get it recharged.

Biker Quote for Today

A true biker finds freedom even in the confines of a helmet.

Someone brought a bunch of gear from a former member to last month’s RMMRC meeting and I managed to snag something that could be useful.

This thing is a Pittsburgh Automotive air compressor that is small enough to fit into the top bag or one of the side bags on the V-Strom just to be there when needed. Nice.

The one thing it did not have with it was any way to connect it to the battery on the bike. It has one of those connectors that you plug into what used to be called the cigarette lighter in a car, but my bike does not have one of those. I needed to go to some auto supply place to find one.

But then I was at the Colorado Motorcycle Expo a couple weeks ago and as I was walking around in an area where there were vendors set up tables filled with parts it occurred to me that someone might have what I needed. Sure enough, I found a pigtail with the right kind of plug and it was $5. I was happy to hand the guy the five.

I could just go ahead and connect it to the battery now, as I have with the connector for my electric vest, but I won’t do that. For one thing, if I do end up getting a second bike that would leave me with only the one bike ready when this thing might be needed.

No, I’ll just stick it in the top bag and let it ride around with me everywhere I go. Hopefully I’ll never need it, but if I do, or someone else needs it, it will be there.

Biker Quote for Today

A world of endless roads is calling. Get out and ride them. — Eric Trow

(This is part two of a series on stripping a motorcycle for parts and listing them on the internet for sale. This is all taking place at Steele’s Cycles.)

With this wrecked 2023 Kawasaki Ninja EX650R now reduced to parts, the good separated from the bad, Tyler loaded all the smaller stuff on a dolly to haul it over to his listing station, where he would prep each individual piece for storage and listing.

But first he needed to deal with the larger parts: the engine, the intact and undamaged rear wheel, and the swingarm. These he hauled outside and doused liberally with degreaser. (He had previously sealed and taped every opening in the engine in order to prevent any water or degreaser from getting inside it.) Nothing that gets listed for sale goes out without being thoroughly cleaned, looking as much as possible like new.

Typically Tyler would use a hose to rinse off the degreaser but on this cold January morning the hose was frozen. So he brought out a large bucket of warm water and poured it over them to rinse. Then they were brought inside to his listing station along with everything else.

That was just the beginning of the clean-up, however. Starting with the rear wheel, Tyler lifted it onto the bench and went at it seriously. Every spot on the wheel was scrubbed clean and then he sprayed it all over with a gloss coating to make it look really good.

He moved to the computer to begin the listing. Steele’s Cycles uses a system called MotoLister, which is designed to simplify the whole process of preparing a part for listing on eBay and then actually putting it up as an item for sale. The screen is quite large and vertically oriented, which minimizes any scrolling that might be needed.

Typically Tyler will search for a comparable part and use that as the starting point but in this case it appears Steele’s Cycles had never broken down a 2023 EX650R, and as the first one, Tyler needed to create a new listing.

Once that was done he opened the listing for the wheel and used the connected camera to shoot more than 20 photos, from every angle and showing every bit of the wheel. In this case, the wheel had a small cosmetic gouge in one spot and he was particularly careful to document that bit of damage. He also made a note in the description of the wheel stating that the damage was there.

At times there can be issues where a customer receives the part and then complains about a ding like this that is clearly shown in the photographs. Did you not look at the photographs? Steele’s will take returns and give refunds but they do not offer free shipping on returns. Rick Steele said he wants the customer to have some skin in the game. Everyone knows these days about customers who order a lot of things online, only to return many of them because there is no cost to them. Not at Steele’s.

After the wheel was clean and the photography was finished, Tyler wrapped it with clear plastic tape and laid a red strip of plastic with an identifying number on it next to the wheel for another photo. He then printed out a tag with all the pertinent information, laid it and the red plastic strip on top of the wheel, sealed those in place with more tape, and then shot one more photo of the whole package.

With a few more entries into the listing system the job was done, Tyler pressed the Enter key, and in seconds this wheel was now available on eBay for purchase. Before his job was done he would do the same for every single part he had stripped off this bike.

When all the parts were listed, they were loaded (with the exception of the motor) into a large blue bin and hauled back into the storage room. Here row upon row of shelves filled with similar blue bins store the individual parts of many, many motorcycles. The location of the bin is logged in the computer and when someone buys a particular part it is retrieved from the bin, matched to make sure it is the right part, and then shipped.

And just like a transplanted heart, a piece of that once sad, broken motorcycle helps another motorcycle go on living.

Biker Quote for Today

I’m not a biker by choice; I’m a biker by destiny.

I wanted to see the actual process of breaking a motorcycle down into parts so over two days I watched Tyler, at Steele’s Cycles, disassemble a 2023 Kawasaki Ninja EX650R that had clearly hit something very hard. The story behind the bike? Totally unknown.

The bike was up on a lift when I arrived and Tyler, with the assistance of Kade, had it running and were testing the motor and all the electrics to determine the running condition of these items. Kade shot photos of the instruments to document their functionality.

Meanwhile, the front end was clearly headed for the trash or the scrap metal bin. While the right fork tube was bent, the left one was busted wide open, with the spring inside now completely exposed.

Naturally enough, Tyler started on the outside, stripping off the plastic body panels. The bigger ones were trash but many of the smaller pieces further back were in good shape and clearly worth resale. These were stacked on an adjacent bench, which got fuller and fuller as Tyler worked.

The gas tank was in excellent condition so that came off and had to drained. Tyler removed the gas cap mechanism from the tank and set that aside with the keys. Later when the ignition switch came off the frame it was bagged with the tank cap and the keys. On other bikes, with keyed elements such as helmet locks, those, too, are included.

The muffler came off and would have presumably worked fine but it was dented so it became scrap metal. Is this axle good or is it bent? It looked straight and it rolled smoothly on the floor. Salvage, not scrap.

Piece by piece the bike came apart with everything salvageable set aside with all nuts, bolts, and washers carefully collected. Tyler might start on removing one item but then find that to get it off he first had to remove something else. The construction of the bike dictated the sequence of its deconstruction.

The oil pan came off and the oil had to be drained. The cooling system came off and the coolant had to be drained. Sometimes it was not a clean job; shops rags are close at hand when needed.

Finally it was time to remove the swing arm. Tyler put a jack and a block under the engine and raised it to take the weight off the rear wheel. First the wheel came off and then the swing arm.

Out at the back end, the taillight assembly was in excellent condition—salvage.

One of the very last things to come off was the wiring harness. Pretty nearly everything else had to be removed because that octopus of copper and rubber winds its way through everything.

Now it was time to release the motor, leaving only the frame attached to the front fork and wheel. The triple clamps seemed not to be bent but they would be examined more closely before the decision was made as to scrap or salvage.

Nothing else was good. The wheel itself was shattered on one side and the brake disks were bent.

Amazingly, the front lights and mirrors were undamaged. This bike hit something really hard but that object must have been no more than two feet high and the upper portion was unscathed.

The very last thing to come off the frame was the ignition. And this, Tyler said, was “The most painful frame ever.” Up to this point Tyler knew the words and had been singing along to practically every country/western song that came on his Pandora feed. For the next 20 minutes Tyler did not sing.

The box with the ignition switch was bolted to the frame with bolts designed not to be removed. The only way to get them out was to drill into them and then tap them with reverse bits and back them out that way. But Tyler drilled and tried the bits, drilled more and tried again—over and over and over. They just would not come. Until they finally did.

What had been a motorcycle was now a collection of larger parts—engine, rear wheel, frame—and two benches of smaller parts. The job was half done.

Biker Quote for Today

You might be a Yuppie biker if you think a wrench is a bitchy woman.